• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons to Change Door Lock

There are a variety of reasons to change your door lock, from upgrading your home's security to re-decorating your entryway. You might also have to change locks if your key is stuck inside or is difficult to turn.

Changing your lock is an easy project that even novice DIY homeowners can tackle. Gather the materials needed to begin.

Remove the old lock

Before installing a new lock it is important to take out the old one from the door. This is essential if you suspect someone else may have keys to the home. It's also a good idea after you've moved into your new home, experienced a burglary or a roommate moved in. The process is simpler than you might think and can be completed in a few minutes.

Start by removing the screws holding the deadbolt faceplate on the frame of the door. To remove the faceplate, you will need to take off screws on both sides. This will allow you to discover what's behind it, and will give you a better understanding of how to proceed in the next steps.

Once you have removed the old faceplate, you'll have to remove the bolt and strike plate. Use a screwdriver to loosen the bolt, and then remove it from the hole in the door. If the bolt is rusty, you may need to use a chisel to hammer it out. If you use a chisel to remove the bolt, take care to not to scratch the door frame.

Before you take down the lock that was previously in use, make sure that your new doorknob and deadbolt fit into the holes in the door. A lot of hardware stores and big box stores have a wide selection of locks and can assist you in selecting the best one. If the lock you bought isn't the right one for your door.

When you're removing the lock that was previously in use, look for small slits or depressions in the handle or around the trim. If you find them, slide a straightened safety pin or a flat screwdriver into them to release the handle and expose screws underneath.

After removing the screw from the handle, you can start removing the knob. To do this, find the set screw located at the base of knob and loosen. Then, take the spindle off.

Install the new lock

It is a good idea to change the repair window locks on your doors frequently particularly if you've been the victim of a break-in. It's easy, affordable and effective to change the lock on your door. With a screwdriver and a few basic instructions the majority of people can handle it themselves. You may also wish to know how to change the key on your door lock to ensure that only you hold the key.

You will need to purchase an additional lock that has the same keyway as your current lock. Most locksmiths will replace your lock for a fee, but you can save money by doing this yourself. You can buy a new lock at a hardware store, or online. A standard deadbolt will usually fit on most doors however, you'll need to measure the space on your window door lock repair to ensure that it fits.

The lock you buy will typically come with a diagram that will show how to install it on the door. You can use it as a guide when drilling the hole, which is much easier than measuring every time. If the template does not line up with your hole then you should return it to the hardware store and get an alternative.

The new lock on the right-hand side of the door. Verify the latch. It should have a label that reads "up" or similar. Make sure that the latch is correctly seated on the plate, and then attach it using the supplied screws.

If you are replacing locks on doors, it's also important to pay attention to the way it's operated. Certain knob locks are right-handed. If you're not careful, you could install the knob on the wrong side of the door, which would make it impossible to lock it from the inside or outside.

You should test the new lock after you have completed. You should be able to lock the door from both the inside and the outside, as well as unlock it using a key. If you aren't satisfied with the outcome, you can always call an expert locksmith to fix the issue.

Test the lock

A door lock that cannot be locked is a hassle and can be dangerous, it could also put your family's security at risk. It's a good thing that it's simple to fix the majority of issues with door locks by performing a bit of troubleshooting and lubrication. First, make sure that your key is properly cut and that the lock assembly isn't soiled or loose. If this doesn't resolve the problem, try lubricating your door lock actuator using graphite powdered.

Then, make sure that the door lock switch, the wiring harnesses, and the actuator connector are working properly. To do this, consult the manual or wiring diagram to determine the function and color-coding of all door lock switch wires. Then, test the wires using a light or digital meter to see whether the door lock actuator is receiving power and ground when the switches are activated. If you see voltage toggles with each switch it means that the switches are in good shape and the actuator is likely to need replacing.

If the switch appears to work but the actuator doesn't move when you turn the knob, it could be an issue with the actuator cylinder itself. The actuator cylinder is outfitted with pins that have a spring-loaded. They prevent the cylinder from moving until the key is inserted, and then they push them upwards to match the height of the key in that area. Then, the cylinder to rotate and let the lock body open, allowing the handle to latch.

If your door lock actuator is still inoperable, you can remove the switch and wires from the actuator by using small screwdrivers to loosen the bolt that locks and then separate the plastic cover that houses the electrical connector. Then you must disconnect the door lock actuator and let it fall down. Then, you should be able to find the two 10mm bolts that keep the actuator in place and remove them. Once the actuator is removed, you should be capable of disconnecting the black electrical connector and pull it out together with the lock and actuator assembly.

replace window locks the key

If you have keys for your deadbolt or door knob, if it is not functioning properly, you must either reset the lock or replace window lock it completely. It's not hard to do this yourself and can save a lot of money. It is recommended to hire a professional locksmith check the locks for any issues before you start. This will give peace of assurance that your home is safe and secure.

Take off the exterior faceplate of the doorknob/deadbolt. If there are screws holding the faceplate in place then use a screwdriver to remove it. Next utilize a flat head screwdriver to remove the interior faceplate. Once you have removed the faceplate, you are able to remove the bolt and screw from the lock cylinder.

A locksmith can decide if you need to Replace Window Locks or rekey your lock. They can also offer suggestions on the most secure measures for your home. They can also make any needed adjustments to the door or frame to ensure a perfect fit. They also provide an assurance on their work.

You must purchase a new lock key before you can rekey it. It's important to use the right key inside the lock. A key that is not properly fitted could damage the internal mechanism and prevent it from functioning. To test the size of a key, just insert it into the lock. If it is flush with the plug, it's the right size. If the pins stick up from the top of the plug the plug, then they're too long.

There are many reasons you might want to change the lock on your door, including:

Rekeying a lock can be an affordable alternative to replacing it if you are moving into the home of an owner who has passed away or if keys are missing. It can also be less invasive than a complete replacement window locks. Rekeying an existing lock may not be possible in certain situations. If the lock has been damaged or repeatedly jammed, for instance it could be the right time to replace it.